Programmable to customize to the installation

Input: TC / RTD / current / voltage / resistance / potentiometer Output: current / voltage / relay points Voltage supply: 21,6 ...253 VAC 19,2...300 VDC Mounting: on DIN - top hat rail / wall Supply for 2-wire transmitter galvanically insulated Accuracy: 0,1% of span LED indicator: normal operation / malfunction / relay active Programming: with programming front

Power supply up to 30 W with small dimension

Input: 94...264 VAC Output: 5 / 12 / 15 / 21 / 24 VDC Efficiency: 77...87% Mounting: DIN - top hat rail Short circuit proof: permanent Overtemperature protection: yes Mains buffering: 40 ms Tolerance nominal voltage: +2% / -1%

Energy saving module for lamps, reduction of energy costs up to 30% possible

for HQL, NAV and fluorescent lamps only little reduction of illumination level power of lamp up to 400 W cylindrical enclosure (standard) with single-hole mounting optional DIN top hat rail lamp voltage 230 VAC connection via terminal block plugable or open cable ends optionally protection IP10 pay back period of approx. 1,5 years possible (at 30%) with VDE certificate

Low cost transducer with input for potentiometer/position sensor
and with a standard output signal

Input pot 0...400 Ohm up to 0...100 kOhm Analog output 4...20 mA (0...10 V) Supply 24 VDC +/-20% (12 VDC, 115VAC, 230 VAC) Zero drift below 0,2%/10K gain drift below 0,1%/10K Easy mounting with top hat rail case Degree of protection IP20 Adjustment of zero and gain

Low cost limit value switch for standard signals for use as an additional
limit switch or as an supplementing for appliance without limit switch

Input 0...10 V, 0(4)...20 mA Relay with change-over contactt Indication of status of relay Switching when above or below limit value Supply 24 VDC +/-20% optional 115/230 VAC Measuring fault less than 0,5% of end scale value, temperature coefficient 50 ppm/K Easy mounting with top hat rail case Degree of protection IP20 Adjustment of limit value and hysteresis

in top hat rail case with two adjustable switch values

Input: 0(4)...20mA, 0...10V,selectable with switches Output: two potatial free changeover contact (250VAC / 3A) Indication of relay state: with LED each Relay behavior (min/max): selectable with switches Limit value: adjustable with digit rotary code switch each Supply: 230 VAC, optionally 24 VAC, 115 VAC, 24 VDC

in top hat rail case for current and voltage,
universal programmable, for general applications

Current input 15yA...10A (AC/DC) voltage input 10mV...1000V (AC) / 1500V (DC) PC - configurable with "DTV - Control" programming software and interface Output 0...20mA, -10...+10V pulse or relay output Supply voltage 24, 115, 230, 400VAC or 12...50VDC Galvanic separation

in top hat rail-case, for sensors, universal
programmable, for general applications

Input resistance thermometer -100...+850°C, thermocouple -100...+1800°C, resistance and potentiometer 10ohm...10kOhm PC - configurable with "DTV - Control" programming software and interface Output 0...20mA, -10...+10V pulse or relay output Supply voltage 24, 115, 230, 400VAC or 12...50VDC Galvanic separation

in top hat rail - case for all
electrical measuring application

4 analog inputs 0(4)...20mA, 0...10V selectable by DIP-switches Adding of input signals One configuable analog output, 0(4)...20mA or 0...10 V, selectable by DIP-switches Accuracy +/- 0,1% of end of scale value Supply voltage 115/230VAC, optionally 24VAC/DC 2-wire transmitters can be supplied directly by the device

head mounting, universally programmable for resistance thermometers,
thermocouples, resistance sensors and mV-sensors

Input: resistance thermometer 2- 3- or 4-wire thermocouples type T, E, J, L, K, N, U, R, S, B, W3 or W5 mV-sensors up to 800mV Configurable for PC, MS-Windows from 3.11 operating surface "DTM-Control" Analog output 4...20mA, reversible, 2-wire technics Temperature linear output for input signal for resistance thermometers and thermocouples Galvanic insulation Optional EX-protection, intrinsically safe EEx ia IIC T4 / T5 / T6 or EEx ib IIC T4 / T5 / T6

Mounting on top hat rail for applications
in food- and chemical industry

Inputs for conductivity gauge head and Pt100 for temperature compensation Outputs temperature and conductibility 4...20mA each Supply voltage 24VAC/DC or 115/230VAC Mounting in 20-terminal top hat rail case for assembly in switch cabinet Measuring range conductivity optional 0...20mS, 0...100mS or 0...200mS, switchable Measuring range temperature 0...200°C

in top - hat rail case

4-channel video signal switch Channel selection "Auto" / "Manual" / "Digital" Switch-over time of the four channels in auto-mode adjustable BNC-jacks for inputs and output Supply voltage 115/230 VAC or 24 VAC/DC, galvanic separation