Suitable to measure temperature, resistance and voltage.
Setting of chracteristic values with a software for visualization via HART protocol.

Input: resistance thermometer / thermocouple / voltage (mV)/ resistance (potentiometer) Output: 4...200 mA current loop, HART protocol Supply: 15...45 VDC out of current loop Accuracy: 0,08...0,12% of range, 0,2...2 K 0,1...7,5 ohms, 10...50 µV Indication: LCD display (backlighting) Galvanical insulation: input / output Settings: with software via HART-protocol Enclosure: diecast aluminium

Programmable to customize to the installation

Input: TC / RTD / current / voltage / resistance / potentiometer Output: current / voltage / relay points Voltage supply: 21,6 ...253 VAC 19,2...300 VDC Mounting: on DIN - top hat rail / wall Supply for 2-wire transmitter galvanically insulated Accuracy: 0,1% of span LED indicator: normal operation / malfunction / relay active Programming: with programming front

in top hat rail-case, for sensors, universal
programmable, for general applications

Input resistance thermometer -100...+850°C, thermocouple -100...+1800°C, resistance and potentiometer 10ohm...10kOhm PC - configurable with "DTV - Control" programming software and interface Output 0...20mA, -10...+10V pulse or relay output Supply voltage 24, 115, 230, 400VAC or 12...50VDC Galvanic separation

for mounting DIN terminal head form B
Output 4...20 mA, programmable

Input: thermoelement or resistance thermometer Output: 4...20 mA current loop freely programmable features EEx version ia IIC T4...T6 with setup program for windows Accuracy up to +/- 0,2 K Degree of protection IP 54/66, when using terminal head for use with terminal head form B

for mounting in DIN terminal head form B
Output 4...20 mA or 0...10 V, programmable

Resistance thermometer Output: 4...20 mA current loop / 0...10 V Supply with output voltage: 15...30 VDC freely programmable features Measuring circuit monitoring With setup program for windows Accuracy 0,2 % FS / 0,2 K For use with terminal head form B

head mounting, configurable ranges selectable by solder bridges
for Pt100 resistance thermometers and thermocouples

Input for Pt100 2- or 3-wire or thermocouples type T, J, K or S Configurable ranges free selectable by solder bridges Analog output 4...20mA, 2-wire design Fault signal for sensor burnout and sensor short circuiting Mounting in connecting head DIN B or with adaptor on top hat rails Optionally: EX-protection, II 1G EEx ia IIB / IIC T4 / T5 /T6

head mounting, universally programmable for resistance thermometers,
thermocouples, resistance sensors and mV-sensors

Input: resistance thermometer 2- 3- or 4-wire thermocouples type T, E, J, L, K, N, U, R, S, B, W3 or W5 mV-sensors up to 800mV Configurable for PC, MS-Windows from 3.11 operating surface "DTM-Control" Analog output 4...20mA, reversible, 2-wire technics Temperature linear output for input signal for resistance thermometers and thermocouples Galvanic insulation Optional EX-protection, intrinsically safe EEx ia IIC T4 / T5 / T6 or EEx ib IIC T4 / T5 / T6

for head mounting, for use as robust
limit value switch or controller

Input for resistance thermometers or thermocouples For connecting heads B-HD / BUS / BUZ Operating with all temperature sensors as "Stand alone" device Continuously adjustable limit value with variable hysteresis (250VAC/5A) Indication status of relay (LED red) Accuracy below +/- 0,5% of end of scale value